Micro Motion RFT9709 Manuel d'instructions télécharger pdf (Page 197)

Using ProLink

Software with Micro Motion

Transmitters

183

Appendix E Transmitter Configuration

Worksheets

The following worksheets, shown in this appendix, should be used for

recording transmitter data during configuration.

• RFT9379 Configuration Worksheet

• IFT9701/IFT9703 Configuration Worksheet

• RFT9712/9729 Configuration Worksheet

1 2 ... 192 193 194 195 196 197 198 199 200 201 202 ... 213 214

Using ProLink 1
Software 1
Transmitters 1
Appendixes 10
Contents 11
1 Before You Begin 15
The ProLink 16
kit and system requirements 16
Customer service 17
2 Getting Started 19
Getting Started 20
2.2 Communication standards 20
2.3 Wiring to the transmitter 21
2.4 Connecting to the PC and 26
2.5 Installing the software 27
Program Group dialog box 28
2.6 Start-up 32
2.7 Connecting to the 32
Menu bar 33
Cannot Find message 33
hour glass 35
Communication options 36
Software communication 37
2.9 Exit 39
3 File Menu: Database 41
File Menu: Database 42
3.2 File selection 42
Directory list box 42
Database command buttons 43
3.5 Load command 45
3.6 Send command 45
Remove command 46
4 File Menu: Print 47
Print setup 48
File Menu: Print 49
Destination 49
Transmitter connections 49
Fields on ticket 50
Figure 4-4. Edit Field Tag 50
Parameter dialog box 50
Separator and book ends 51
4.3 Print 52
4.4 Interval print 53
4.5 Update rate 54
Figure 4-7. Print - View 54
Application - Update 54
Rate dialog box 54
Print file 55
5 File Menu: 57
Error and Change Log Files 57
Error log options 58
5.2 Change logging 58
Log file name 59
Change log options 60
6 View Menu: Variables 61
View Menu: Variables 62
6.3 Output levels window 63
7 View Menu: Status 67
View Menu: Status 68
Table 7-1. Status indicators 68
7.2 Fault outputs 70
7.3 Critical indicators 70
Critical indicators 71
Operational indicators 76
"Slug Flow" 77
Analog and frequency 78
7.5 Informational indicators 80
Zero indicators 81
Analog Fixed indicators 83
"Burst Mode" 83
Informational indicators 84
8.1 Overview 85
Flow calibration factor 87
Sensor or transmitter 90
Field flow-calibration 90
8.3 Density factors for 92
Density characterization 93
8.4 Density factor for 94
IFT9701/IFT9703 and 94
Slug flow limits 95
8.6 Temperature factor for 96
Configure Menu: Characterize 100
8.7 Pressure compensation 100
Real-time compensation 100
Compensation for stable 101
Transmitter Variables 105
9 Configure Menu: 105
Overview 106
9.2 Flow units 107
Flow units 108
Special flow units 110
Software with Micro Motion 111
Transmitters 111
Special units of mass for 112
Figure 9-6. RFT9739 for Gas 114
9.3 Density units 114
API gravity 114
API standard volume 115
9.4 Temperature and pressure 116
9.5 Flow cutoffs 116
Flow cutoffs 117
Problem: 117
Solution: 117
9.6 Flow direction 118
9.7 Internal damping 119
Internal damping 120
10 Configure Menu: 121
Transmitter Outputs 121
RFT9739 outputs 123
IFT9701/IFT9703 outputs 123
RFT9712/RFT9729 outputs 123
10.2 Frequency/pulse output 123
Frequency/pulse output 124
Maximum pulse width for 125
K-factor 126
10.3 Milliamp outputs 126
Milliamp output variables 126
Range limits 127
Milliamp output flow 127
RFT9712/RFT9729 127
Added damping on 128
10.4 Fault indicators for 129
Configuring fault 130
10.6 Control output from 131
11 Configure Menu: 133
Transmitter Information 133
11.2 Transmitter database 135
11.3 Pressure input for 136
Pressure input for RFT9739 137
12 Configure Menu: Events 141
Configure Menu: Events 142
12.4 Reading event states 144
13 Configure Menu: 145
Meter Factors 145
Configure Menu: Meter Factors 146
13.3 Entering meter factors 146
14 Calibrate Menu 147
Calibrate Menu 148
Diagnosing zeroing failure 150
Convergence limit 150
Zero time 151
14.4 Density calibration 152
Density calibration for 153
Table 14-2. Density of air 155
Table 14-4. Density of water 157
IFT9701/IFT9703 158
14.5 Temperature calibration 162
14.6 Milliamp output trim 165
Preparing for milliamp 165
Performing milliamp 166
15 Test Menu 169
Milliamp output testing 170
Applications Menu Help Menu 171
Configure Menu: 171
Calibrate Menu Test Menu 171
Test Menu 173
16 Applications Menu 175
Applications Menu 176
16.3 Application builder 177
17 Help Menu 179
Help Menu 180
17.3 Keyboard 180
17.4 Using Help 180
17.5 Context-sensitive Help 180
Getting around in Help 181
Jumping from one Help 182
17.7 Glossary of terms 182
B.1 Uploading files 185
Uploading files 186
B.2 Downloading a 188
Flow and Density 191
Worksheets 197
• RFT9379 Calibration Record 203
Flowmeter Calibration Records 204
Micro Motion Inc. USA 214
Worldwide Headquarters 214
Micro Motion Europe 214
Micro Motion Asia 214

Commentaires sur ces manuels

Pas de commentaire

Micro Motion RFT9709 Manuel d'instructions Page 197

Commentaires sur ces manuels